using a drill for raising the main

Use this forum to discuss anything that doesn't fit anywhere else.
ouroe
Posts: 7
Joined: Tue Jan 10, 2017 9:56 pm
Location: Tucson/San Carlos, Mexico

using a drill for raising the main

Post by ouroe »

I'm a new owner of a Freedom 38, and I've seen some old posts about using an offset drill to help raise the main. Doe anyone have some current input on what works? I'm curious about:
using a battery operated or plug in? I have an invertor.
What brand ((I've heard Milwaukee)?
How much power I need- 7 amps, 18v.?
What kind of adapter do I need to specify to fit the winch?
thanks, in advance.

User avatar
rvivian
Posts: 210
Joined: Sun Feb 21, 2010 2:08 pm

Re: using a drill for raising the main

Post by rvivian »

Heart's Desire
Freedom 30
Shelton, WA

jdpandlp
Posts: 65
Joined: Mon Dec 08, 2008 8:59 am

Re: using a drill for raising the main

Post by jdpandlp »

I have used the Winchrite for 6 years on my 39 Express and have nothing but good things to say about it. Used a battery powered drill before that and though it worked it did not come close to being as good as the winchrite has been.

User avatar
Ereiss
Posts: 354
Joined: Sat Dec 06, 2008 12:32 pm

Re: using a drill for raising the main

Post by Ereiss »

Very happy with the Milwaukee right angle drill. Used it for eight years. No experience with the Winchright
Ed Reiss
Being There
F38 - #154
out of Marion, MA

wcwcwc
Posts: 94
Joined: Fri Dec 05, 2008 12:00 pm
Location: F36 Padanaram, MA

Re: using a drill for raising the main

Post by wcwcwc »

I used an 18v Nicad battery Milwaukee 3/8 drill on my f36 for ten years. It was not a right angle and also not an impact driver. It raised the main to about 3 feet from the top requiring very little work to get it up and tightened properly. I would be careful not to get an impact driver or hammer drill fearing damage to the winches. A Winch Bit is all you need to connect drill to winch.
Bill Cormack
Formerly Sailing F-36 "Hard Earned" out of New Bedford Yacht Club, Padanaram, MA. Now a member of Pelagic Sailing Club a New England based club whose members are about half boat owners and half crew.

rafontaine1
Posts: 46
Joined: Sat Dec 27, 2008 11:34 am
Location: Liberte, F36, 1986, Portsmouth RI

Re: using a drill for raising the main

Post by rafontaine1 »

I've used the Winchrite on my F36 for the last two years and works great. I used the Milwaukee right angle drill to raise my rigging guy up the mast and found the Winchrite to be easier in that it can be handled by one hand once fitted in place. Not as bulky.
Rich Fontaine
s/v Liberte
Freedom 36, 1986
Portsmouth, RI

ouroe
Posts: 7
Joined: Tue Jan 10, 2017 9:56 pm
Location: Tucson/San Carlos, Mexico

Re: using a drill for raising the main

Post by ouroe »

Thanks for all the input-good to know.

User avatar
sailmon
Posts: 237
Joined: Sun Feb 22, 2009 6:53 pm

Re: using a drill for raising the main

Post by sailmon »

I bought the 28V half inch Milwaukee right angle a couple of years ago - does a great job raising main on our F38. Will also pull me up the mast for inspections/repairs. While I looked at the Winchrite and really liked it, I opted for the Milwaukee becasue I can also use it as a drill when doing installs/repairs on the boat that require the accessibility of a right angle drill or the power & chuck size needed by a larger hole saw.

One word of caution docunmented in a variety of commentaries on the Milwaukee. If you have a 2 speed winch and use the drill in the higher speed direction, the chuck on the drill tries to unscrew itself - resulting in the securing screw inside the chuck snapping off. This usually happens when the screw loosens a bit - allowing the chuck to begin unscrewing. While some people have addressed this issue by unsing locktite I am reluctant to install the screw in a way that makes it difficult to remove if I need to take the chuck off.

I've found a much better approach is to always use the drill in reverse - which operates the winch in the low speed highs power direction. While this does raise the sail a bit slower, it is easier on the drill motor and most importantly pulls the sail up slowly enough that damage to sail/rigging is less likely if something hangs up. I can think of no reason why it would be necessary to raise our main in 6 seconds. 30-40 seconds seems to work just fine.

Either way, I just retired and am making preparations for retirement cruising and really enjoy not having to pull our 85# main up by hand grinding.
Sailmon (Captain Bob Allenick)
S/V Her Diamond
1991 Freedom 38
Cleveland, OH

User avatar
hxschiller
Posts: 88
Joined: Sun Dec 07, 2008 7:55 pm
Location: Mull 28 - "Impulse" on NW Creek in New Bern, NC

Re: using a drill for raising the main

Post by hxschiller »

Note that there are two flavors of Loctite. Blue Loctite is intended to secure the screw/bolt; red Loctite is intended for much more serious/severe vibration, and is much more resistant to being removed. I only use red Loctite when it's critical or dangerous if the screw becomes undone. BTW both Loctites do a good job of preventing the fastener threads from corroding. Assuming that the screw in the bottom of the chuck is NOT stainless steel, the anti-corrosive characteristic seems valuable.

Kimber
Posts: 18
Joined: Fri Aug 03, 2012 11:18 am
Location: St Thomas USVI

Re: using a drill for raising the main

Post by Kimber »

I have been using an old 1/2" 120volt Milwaukee right angle drill to raise the sails on my Freedom 39 Express for about 4 years. It works great. I have a winch bit fitting for it http://www.winchbit.com/
I plug it into the inverter and don't have to worry about a battery going dead or needing to be recharged. It has plenty of torque to get people up the mast and can still be used to drill holes at low rpm with lots of power if needed.
1985 F39 Express

Post Reply